Workpiece carrier circulation system 180° curve

Versamove standard workpiece carrier circulation system with 180° round belt curves

This circulation system is used to feed workpieces on workpiece carriers to a processing cell, e.g. a robot in a protected area. On one of the two long sides, the workpiece carriers are stowed and separated and, for example, loaded by a worker at a manual workstation. The workpiece carriers are then routed to the parallel conveying path where they are also stowed and separated and fed to the processing machine in cycles. After processing, the workpiece carriers are returned to the original side and fed to the worker for unloading and reloading.

26.420,00 €

Price plus VAT and shipping

Dimensions: LxWxH 5864 x 938 x 900 mm
Workpiece carrier: 400 x 400 mm
Total load: 12 kg/workpiece carrier (incl. components and workpiece)
Electrical voltage:  230/400 V, 50 Hz; 24 VDC; degree of protection IP 54
Compressed air supply:  6 bar
System environment: Dry (air humidity < 60%), not abrasive
Temperature range: +5° C to + 40° C
Incl. sensor system, without cable
Including controller and electrical installation
Including pneumatic installation
Without protective device guard

2 accumulating roller chain conveyors SRF-P 2045 AF
Conveyor length: Approx. 5000 mm
Conveyor width: 418 mm
Workpiece carrier width 400 mm
Conveyor height: 900 mm
Drive version: Direct head drive
Motor orientation: 0°
Output: Approx. 0.25 kW, 230/400 V, 50 Hz
Make: SEW asynchronous gearmotor
Max. distributed load:   30 kg/m
Max. total load: 120 kg/conveyor
Chain design: ½" accumulating roller chain with steel rollers
Chain guide: Integrated wear strip made of PE 1000
Conveyor speed: 12 m/min constant at 50 Hz
Chain tension: Spring-loaded clamping unit
Chain lubrication: Central lubrication unit for chain conveyor ZSE-2045

2 180° round belt curves KER 2045
Non-driven version. The conveyor is driven by means of a coupling with the reversing shaft of the subsequent conveyor. This results in a space-saving design for tight curve radii.
Payload: Max. 12 kg
Curve angle: 180°
Workpiece carrier width: 400 mm
Speed: 6 m/min constant at 50 Hz motor orientation: 90°
Output: Approx. 0.25 kW, 230/400 V, 50 Hz
Make: SEW asynchronous gearmotor
Medium of transport: Round belt ø 10 mm
Note: Due to the curve, the workpiece carriers may only be transported individually and not stowed.

10 workpiece carriers WT 2045
Aluminium base plate (8 mm) and plastic runners, centring bushes, damping elements
Size: 400x400x28 mm
Design: Without workpiece holders, drilling template provided by the customer             

6 stoppers or separation units
Design: SU 400 undamped
Position detection: Sensor groove for reed contact
Control: Single acting, depressurised

2 positioning units PE 2045
Positioning in X, Y and Z directions
Stroke: 30 mm (8 mm above the conveyor level), via linear roller bearings and guide rods
Cover: VA sheet metal
Repeat accuracy: +/- 0.2 mm

Stand system
Made using mk profile system with levelling feet and retaining angles for floor fastening.
Set the conveyor level using the spindles in the levelling foot (+/- 20 mm).

Electrical and pneumatic equipment
Completely installed on a separate control cabinet and wired ready for connection. The control cabinet is mounted on the system.

Contact

For custom requests, please contact our technical sales department at info(at)mk-group.com, by phone at +49 2284598-­0 or using the contact form below.

* mandatory fields

Allowed file formats: JPG, PNG, Word, Excel, PDF, STP ... (not larger than 32MB per file)