The Compact Workpiece Carrier Circulation System
Versamove standard is the most compact of the Versamove systems. It offers fully electric functional units and affordable curve modules. Due to the specially developed 45 mm aluminum profile for the basic structure of the entire system, it is also compatible with other systems and workpiece carriers available on the market.
Versamove standard transports workpiece carriers from 240 x 240 to 400 x 400 mm, with custom dimensions or dimensions in 80 mm intervals possible. The system can move pallets weighing up to 40 kg. The special feature of this system is its affordable curve modules, which are equipped with a flat top chain or, for compact curves in tight spaces with a round belt.
Versamove standard electric
For efficient and environmentally friendly process automation
The functional units, HQZ lift-and-transfer conveyor, HDE lift-and-rotate unit, PE lift-and-locate unit and SU/SD stopper are also now available in fully electric variants. This completely eliminates the need for a compressed air supply. This version can be retrofitted into existing Versamove systems with ease. Depending on whether you already have pneumatic infrastructure, it may make more sense to replace the modules with electric ones gradually or in one go.
- Length: 600-6000 mm
- Total load: 200 kg
- Speed: up to 30 m/min
- Drive variants
- Timing belts
- Length: 600-6000 mm
- Total load: 500 kg
- Speed: up to 30 m/min
- Drive options
- Accumulating roller chains
- Length: 500-6000 mm
- Total load: 400 kg
- Speed: up to 18 m/min
- Drive options
- Flat top chain
- Aluminium support plate (steel optional)
- Positioning sockets in the support plate for positioning and rotating the workpiece carrier
- PE wear strips (steel optional)
- Integrated bumper
- Antistatic design optional
- Total load up to 40 kg
- Width and length: 240, 320, 400, 480 mm
- Low height
- 14 mm lift motion with stepper motor via eccentric
- Guided by linear roller bearings and guide rods
- Inductive position detection
- Stopping via wear strip with stop edge
- Loads up to 40 kg
- Speeds 10 m/min.
- Low height
- 16 mm lift motion with stepper motor via eccentric
- Guided by linear roller bearings and guide rods
- Inductive position detection
- Rotation 90° steps
- Loads up to 40 kg
- Low height
- 5 mm lift motion with stepper motor via eccentric
- Guided by linear roller bearings and guide rods
- Positioning in the X, Y and Z directions
- Positioning sockets in the workpiece carrier’s support plate for positioning
- Inductive position detection
- Repeatability: ± 0,2 mm
- Damped and undamped stopping
- Electrical or inductive stopper detection possible
- Dual acting
- Direct mounting on the conveyor frame (no additional holders required)
- Permissible load depends on the stopper variant and the conveying speed
- Pneumatic lifting motion 20 mm
- Guided by linear roller bearings and guide rods
- Manual tensioning device included
- Inductive position detection (reed contact optional)
- Top cover available as stainless steel sheet (clear Makrolon optional)
- Loads up to 40 kg
- Speeds of 6; 9; 12; 15 and 18 m/min
- Custom rotation speeds
- Pneumatic lifting and turning motion
- Guided by linear roller bearings and guide rods
- Inductive position detection (reed contact optional)
- Loads up to 40 kg
- 90° and 180° rotation
- Pneumatic lifting motion
- Positioning in the X, Y and Z directions
- Positioning sockets in the workpiece carrier’s support plate for positioning
- Inductive position detection
- Repeatability: ± 0,1 mm
- Cylinder stroke: 30 mm
- Damped and undamped stopping
- Electrical or inductive stopper detection possible
- Single or dual acting
- Direct mounting on the conveyor frame (no additional holders required)
- Permissible load depends on the stopper variant and the conveying speed
- 90° and 180° in the smallest space (other angles possible on request)
- Particularly suited to parallel conveyor lines that are positioned close to one another
- Replaces lift-and-transfer units and lift-and-rotate units (workpiece maintains its orientation)
- Available with its own drive or can be driven by the adjoining line
- Medium of transport: Round belt
Contact
For custom requests, please contact our technical sales department at info(at)mk-group.com, by phone at +49 2284598-0 or using the contact form below.